1. Select the suitable rack steel material
The low temperature environment has specific requirements for the application of steel products, and should have good low temperature toughness and ductility, so as to avoid brittle failure. Common carbon structure steel Q235 commonly used in the rack, Q235A, Q235B, Q235C, Q235D, Q235E in different grades, mainly because the impact temperature varies. A means no impact. B is above 20 C, C is above 0 C, D is above -20 C, E is above -40 C, A to E, and the difference of impact temperature in their respective properties.
Secondly, the common carbon structure steel A/B/C/D also represents the different content of traces elements. Because of the different content of trace elements, the quality grade of A/B/C/D is getting higher and higher, and the performance of the low temperature is getting better and better. Generally speaking, Q235D will be used as the main material of cold storage rack. The manufacture of fasteners is usually made of high nickel chromium (such as Cr18Ni9 type) alloy steel or nonferrous metal (such as copper and aluminum) in low temperature environment, which almost do not show low temperature brittleness. The thermal expansion coefficient of steel material is 1.2 x 10 5/ C, and the thermal expansion coefficient of concrete is about 0.7 x 10 5/ C, which is close to each other, and can be effectively connected when the temperature difference is within 40 degrees C.
2. Select the appropriate rack system
Cold storage can be described as "inch inch gold" to describe, choose the right rack system, for customers to use each cubic meter, to reach the maximum warehouse utilization rate, is the rack supply enterprises need to focus on factors. The following are several common types of cold storage racks:
The combination of storehouse and frame: the combination of warehouse and rack is an ideal high position storage system, which directly stores the roof and side walls of the warehouse on the rack, and eliminates the construction of the warehouse. The utilization rate of warehouse is the highest and the long-term investment return rate is the highest. At the same time, the technical requirements for the racks are also high.
The common shuttle rack system, the entry type rack system and other rack types, such as the double depth pallet rack, the rear push rack system and the gravity type rack system, are selected mainly according to the different requirements of the customers. In general, there is no best, only the best.
3. Choose the proper way of surface treatment
Spraying (epoxy polyester electrostatic powder spraying) is the most common rack surface treatment. It is not very harsh for cold storage, which is very suitable for corrosion and rust prevention. It has good applicability and economy.
4. Other considerations
Other factors should be considered in the design of cold storage racks, such as the selection of welds in the cold storage, which should correspond to the material and welding process requirements of the welded material and ensure the welding quality of the weld. The characteristics of frost in the cold storage should be considered. The weight gain should be considered properly when calculating the selection of racks, and the corrosion resistance requirements of the customer refrigeration and defrosting process on the structure spray coating should be considered.
The cold bridge of the anchor bolt at the pillar foot of the rack column (the corner of the outer wall, the angle of the inner and outer walls, the roof of the building and the outside of the outer wall) will produce the phenomenon that the water mist is adsorbed on the wall, and the effect of dew condensation in the wall of the wall, "tears", "perspiring", "moldy", the damp and mildew of the house, will appear. Worry and avoid.
For each project, whether the above factors are considered or considered economically and reasonably, we need to make specific analysis based on specific circumstances. Combining with engineering practice, Hercules understands and responds to the actual needs of customers, and creates economic benefits wholeheartedly for customers, which is the fundamental purpose of engineering design.
Compared with the spray, hot dip galvanized (hot dip galvanized and hot dip galvanized) high cost, high cost around 40%. Hot dip galvanizing is to immerse steel after derusting into molten zinc at 500 degrees or so, so that the surface of steel members can be attached to zinc layer, so as to achieve the purpose of anticorrosion. If customers have high requirements for corrosion and rust protection and are not very sensitive to cost, hot galvanized surface treatment can be adopted.
In many cases, it can be handled flexibly. According to the specific conditions, different surface treatment methods are adopted to achieve the optimal solution, such as the entry system, the main rack is sprayed on the main rack, and the ground guide can be hot-dip galvanized to achieve the best cost advantage and use effect.
Jracking is specialized in producing various pallet rack, cantilever rack, electric mobile rack storage system, mezzanine and platform, shuttle car automatic storage system, push back rack, longspan shelving, rivet shelving, drive in rack, carton flow rack, stacking rack and other related storage equipment.
Jracking strictly implements ISO9001, FEM10.2.02, SEMA, and AS4084-1993 standard in all operations. Jracking offers a wide range of products to meet all of your order fulfillment & material handling needs: Teardrop pallet rack, Dexion pallet rack, European pallet rack and other Work Apparatus. Whether you are looking to populate an entire warehouse or you are in need of a single piece of equipment, Jracking has a solution for you.